Create: Massive Turbines

Pipe your boiler steam into big multiblock turbines, then turn all that spin into FE.

Join my Discord server

Create

About

Most Create bases end up with the same thing: a maxed boiler covered in Steam Engines. I wanted somewhere to go after that, so Massive Turbines lets you pipe the steam out of your boilers and into big multiblock Steam Turbines. The longer you build them, the more you get out of the same steam. Hook one up to an Industrial Alternator and you've got Forge Energy too.

I tried to keep it all feeling like Create: copper and brass, regular Fluid Pipes, casings you click into place, and a Ponder scene for everything.

Steam pipes

It all starts with the Steam Export Pipe. Stick one on the side of a boiler and it has a little pressure gauge that shows the boiler's level. The boiler also counts as running even if there's no Steam Engine on it.

From there you just use Create's Fluid Pipes. Connect them to the export pipe and the whole run turns into heavy steam pipe. If you break the line, the loose end goes back to being a Fluid Pipe, and it joins up again when you fill the gap.

Put a Steam Gauge in the line to see how much of your steam is being used. Look at it with goggles and it'll tell you which boilers are feeding it, what's using the steam, and why you're running short.

Steam Engines sitting on the boiler get their steam first and the pipes get what's left. You can also put Steam Engines right on a steam pipe. If there isn't enough to go around, everything on the line gets an equal share.

Steam turbines

Turbine Fan, Large Turbine Fan and Huge Turbine Fan

A turbine is a row of fans, anywhere from 1 to 9, all the same size, with a ring of Turbine Casing around each one. Every layer you add makes it more efficient than Steam Engines running on the same steam.

Fan Ring Efficiency per layer At 9 layers Steam it can take
Turbine Fan 3x3 20% 180% 1 maxed boiler
Large Turbine Fan 5x5 33% 297% 3 maxed boilers
Huge Turbine Fan 7x7 50% 450% 5 maxed boilers

For reference, a Steam Engine makes 16,384 SU per boiler level. A full 9-layer Huge turbine running on five maxed boilers puts out around 6.6 million SU. More steam makes it spin faster, anywhere from 16 to 192 RPM, but the SU stays the same at any speed. You can take the shaft off either end.

When the turbine is done, the casing closes up into a big eight-sided copper shell. The fans take a moment to spin up and wind down, and the bigger the turbine, the deeper it hums.

Industrial Alternator

The alternator works a lot like the turbine: a row of 1 to 7 Industrial Alternator Cores, each with a ring of Industrial Alternator Casing. Spin it with a shaft from either end and it makes FE.

An open and an encased Industrial Alternator

You set its Resistance on any core's value panel, from 0 to 1024 SU per RPM. It starts at 64, and changing one core changes the whole alternator.

It makes 1 FE per tick for every SU it takes, and each core after the first adds another 50%, so a 3-core alternator gets twice as much FE out of the same SU as a single core.

Power goes out into any energy block touching it, on any side, and other mods can pull from it as well. It holds 500,000 FE per core, but whatever it makes each tick goes straight out, so the storage never slows it down.

It also whines while it spins, and the pitch goes up with speed and resistance.

Building

You don't have to place every casing by hand. Hold Turbine Casing and right-click a turbine to fill in all of its rings at once, or hold a fan and click a fan to add the next layer. You'll see a see-through preview of where everything goes, just like with Create's shafts. The alternator works the same way. Sneak if you'd rather place blocks one at a time.

Hit a finished turbine with a wrench to give it windows. Glass strips run down the sides and the ends turn into clear panes, so you can watch the fans going. Wrench it again to close it back up. It's a bit quieter closed.

The alternator does the opposite. It starts open with its copper windings showing, and a wrench covers it in louvred steel plates. Wrench it again to open it back up.

Ships

If you play with Sable or Create Aeronautics, turbines, steam pipes and alternators all work on ships. Build them on a ship that's already flying, or assemble the ship around them, and they keep running in the air.

Aeronautics' Steam Vents count as Steam Engines here, so they take their share of the boiler first and the export pipes get the rest. Neither mod is required.

Settings

Almost all of the numbers above can be changed. Go to Mods > Create: Massive Turbines > Config and you'll find a tab for each part, with a tooltip and a Reset button on every setting:

  • Turbine: efficiency and steam limit for each size, the speed range, SU per boiler level, the most layers, and how long it takes to spin down.
  • Alternator: FE per SU, the bonus per core, the most cores, storage per core and the Resistance range.
  • Steam Pipes: how much steam a passively heated boiler gives, and how long a pipe run can be.
  • Turbine Sound and Alternator Sound: volume, pitch and range for each size.

On a server, the world settings are synced to everyone and only operators can change them.

Requirements

  • Minecraft 1.21.1 with NeoForge 21.1.219 or newer, and Create 6.0.10 or any later 6.0 version.
  • Sable and Create Aeronautics are optional.
  • It needs to be on both the client and the server. Feel free to put it in your modpack.

Create: Massive Turbines Team

profile avatar
Owner
  • 6
    Followers
  • 4
    Projects
  • 14.1K
    Downloads
Donate

More from Lixvach